STEP BY STEP INSTRUCTIONS Cool. Sat 4. 00. 0, 5. 00. FOR DIRECT CONNECTION W/OUT A DONGLESolution. Every step required to use your Cool. Sat Receiver with this IKS provider is explained in detail. The entire setup process is quite simple and should take less then 1 hour from start to finish. If you wish to begin viewing TV in the shortest possible time it is imperative that you carefully follow the instructions in this guide. Do not deviate nor skip any of the steps. IMPORTANT ! READ BEFORE PRECEEDING FURTHER TO PREVENT POSSIBLE DAMAGE TO YOUR CS, SWITCHES OR LNB's ALWAYS TURN YOUR RECEIVER OFF USING THE REAR SWITCH WHEN ATTACHING OR REMOVING CABLES. PREFERABLY IT SHOULD BE UNPLUGED WHEN CONNECTING OR REMOVING ANY CABLE TO OR FROM IT. A Computer with an Internet Connection 2. DB9 RS2. 32 STRAIGHT THROUGH SERIAL CABLE or if your computer does not have a DB9 RS2. COM port you can use a USB to SERIAL ADAPTER along with your DB9 RS2. SERIAL CABLE. A USB to SERIAL DRIVER for your OS must also be installed on your PC. The rq- sssp- client software and the included rq coolsat firmware (bin files) for your receiver which you can download from here: RQ SOFTWARE & FIRMWARE FOR COOLSAT 4. K, 5. K and 6k rev 0. Neusat 6000 Premium: Coolsat 7100 micro pvr : Coolsat. Coolsat 6000, Coolsat Premium, free to air satellite receiver, Coolsat 6000 Premium. Coolsat 6000 Premium Manual Pdf. Coolsat 6000 FTA Files. Free fta coolsat 6000 how to's. Replacing the Coolsat 6000 Premium this new. Guides for your Free-to-Air receiver BIN Files Updates for Pansat. Coolsat 6000 Premium Fta UpdateCoolsat 6100 Bin Files - Download Free Apps. Coolsat 6000 Premium, Coolsat 6100, Coolsat 8100. Get all the Coolsat FTA Files and Coolsat Bin Files including Cool. STEP BY STEP INSTRUCTIONS CoolSat 4000, 50 FOR DIRECT. Learn more about Neusat sp 6000. Coolsat 6000 Premium: Coolsat. All you have to do is click the bin files. Coolsat Pro Loader v. Use the following link to download the Cool. Sat Loader: COOLSAT LOADER V2. A Coolsat channel list (*. MANUAL REPAIR OF THE Ca. ID MISMATCHThere is currently a Ca. ID MISMATCH problem with the Coolsat CS 5. CS 6. 00. 0 receivers and DN. There are two ways to resolve this mismatch problem with the Coolsat Receivers. You can download a Coolsat CHANNEL LIST and load it into your CS receiver as explained in Step 8 of this guide or you can MANUALLY REPAIR THE Ca. ID MISMATCH problem using the following procedure. After you have followed all the STEPS in this guide with the exception of (Step 8 - Loading a Channel List) and have reached (STEP 9 - Watching TV) Turn your Coolsat Receiver ON and set it to a known nfps channel e. Start your RQ software (rq- sssp- client. TV will now show the channel you selected SCRAMBLED. To UNSCRAMBLE the channel follow this procedure: a. On your Coolsat Remote PRESS 8. BLUE button and a Window will open on your TV Screen showing two Ca. ID options. Option 1 is Nagravision (1. Option 2 is Nagravision (1. Select Option 2 Nagravision (1. OK. Within a few seconds the channel you have selected will come in UNSCRAMBLED. After selecting Option 2 (1. TV stating . EVERY TIME YOU CHANGE TO A CHANNEL YOU HAVE NOT PREVIOUSLY USED YOU WILL HAVE TO FOLLOW THE ABOVE PROCEDURE TO UNSCRAMBLE YOUR CHANNEL, HOWEVER YOU ONLY HAVE TO DO THIS ONCE FOR EACH CHANNEL YOU SELECT AS THE CORRECT Ca. ID INFORMATION IS THEN SAVED BY THE COOLSAT RECEIVER. THE ADVANTAGE TO USING THIS MANUAL METHOD TO CORRECT THE Ca. ID MISMATCH IS THAT THE CHANNEL LISTS LINKED IN THIS GUIDE AND ANY ADDITIONAL LISTS THAT MAY BE POSTED IN THE COOLSAT FILES SECTION HAVE BEEN CREATED BY MEMBERS WHO ARE POSTING THESE FILES TO SHARE WITH OTHER MEMBERS. THERE IS NO GUARANTEE THAT THESE LISTS CONTAIN ALL THE NFPS CHANNELS AVAILABLE ON THE VARIOUS SATELLITES. IN FACT MOST DO HAVE SOME CHANNELS MISSING AND THOSE CHANNELS MAY OR MAY NOT BE OF INTEREST TO YOU INDIVIDUALLY. THE MANUAL REPAIR METHOD FOR THE Ca. ID MISMATCH WILL ALLOW YOU TO VIEW ALL OF THE AVAILABLE NFPS CHANNELS, ASSUMING THAT YOUR DISH(s) ARE PROPERLY POINTED AND YOU HAVE A GOOD QUALITY SIGNAL FOR EACH OF THE SATELLITES YOU ARE USING, YOUR ANTENNA SETUP IS CORRECT AND YOU HAVE PROPERLY SCANNED IN AND SAVED THE CHANNELS FROM EACH SATELLITE. THE DISADVANTAGE TO THE MANUAL METHOD IS THAT WHEN SELECTING CHANNELS TO WATCH FOR THE FIRST TIME IT WILL REQUIRE A FEW EXTRA SECONDS UNTIL THE STATION COMES IN UNSCRAMBLED. CHANNEL LISTS ARE AVAILABLE FOR DOWNLOAD FROM THE COOLSAT FILES SECTION OF THE FORUM. THERE ARE NUMEROUS FILES AVAILABLE. I SUGGEST THAT YOU LOOK FOR THE LATEST FILE AVAILABLE THAT HAS THE CAID REPAIR FOR THE SATELLITES YOU PLAN ON USING. No claims are made as to how complete these lists are. I RECOMMEND THAT BEFORE DOWNLOADING ONE OF THE CHANNEL LISTS LINKED BELOW THAT YOU CHECKOUT THECOOLSAT FORUM TO SEE IF THERE HAVE BEEN ANY POSTS POSITIVE OR NEGATIVE IN REGARDS TO THE LIST YOU ARE INTERESTED IN. Unzip RQ software you will now have: 1. COOLSAT FIRMWARE/BIN FILES Included in 3. STEP 7 provides STEP by STEP Instructions on updating your Coolsat with the correct included Coolsat firmware. If you have downloaded a Coolsat Channel list - unzip it If you have downloaded a Coolsat Channel list you will need to first unzip the archive and you should then have a file with an . STEP 8 provides detailed instructions on loading a channel list into your Coolsat STEP 2. VERIFY YOUR FILE EXTENSIONS ARE VISIBLE In order to edit and properly save your rq- sssp- client. VERIFY COM PORT # To check your COM PORT go to: CONTROL PANEL > SYSTEM > DEVICE MANAGER > . If using a USB to SERIAL ADAPTER and do NOT see . VERIFY PORT SETTINGS RIGHT click. COM (port#) > properties > port settingsand they should be 1. EDIT THE RQ- SSSP- CLIENT. CONF FILE The following info must be edited into your rq- sssp- client. COM PORT # if it is other than . Your 1. 4 digit ACCESS CODE. The SERVER (6. 2. PORT # for the Server included in the email with your access code. Editing these items, the COM PORT, YOUR ACCESS CODE, SERVER and the PORT ADDRESS into your rq- sssp- client. You should NOT make any other changes to the rq- sssp- client. Open. NOTEPADand. MAXIMIZE the WINDOW. Go to: MENU > FILE > OPENand you get the open dialogue box. Figure A In NOTEPAD with your WINDOW MAXIMIZED EDIT THE FOLLOWING: A. YOUR COM PORT If Device Manager verified your PC COM PORT AS COM . If you com port number was other than . NOTE: When editing the card. Enter your NFPS ACCESS CODE. Replace twice (example below) YOURACCESSCODE with your 1. Make sure you do not inadvertantly remove the : that seperate the two access codes. C. ENTER THE CORRECT SERVER IP# Replace where it says SERVER with: 6. D. ENTER YOUR PORT #Edit the port number by replacing the ##### with one of the 5 digit port #'s that you received with your access code. NOTE: The port numbers and servers you were initially assigned are subject to change. Should your service be interupted the first step you should do is check the announcement forum at this site to see if there are new port or server assignments. If this occurs simply re- edit your conference file with the latest server/port info and save as instructed below. VERIFY EOF (INVISIBLE END OF FILE CHARACTER) IMPORTANT !! Before you SAVE this file as instructed below,verify the EOF by placing your cursor at the end of the card. The . conf file will not work if this is not included. F. VERIFY EDITThe last line of your . IP# you were instructed to use along with one of the port numbers you were assigned to replace the #####. If it appear on two lines in these instructions it is due to width limitations on forum posts. EXAMPLE of card. It is IMPORTANT that you follow the next instructions EXACTLY as written. Create New Folder for the RQ software The Save as Dialogue box has 4 drop down menu boxes. The first is at the top and it says . Use that dropdown menu of . Then you should create a NEW FOLDER by clicking on the . After clicking on the new folder icon you will then see a folder appear with the words new folder. I named my folder CS but you can call it anything you wish. After you type in the name of the folder hit the enter key twice. Once saves the name and the second opens the folder. You should now see the name of your new folder in the . Save the edited rq- sssp- client. The next 3 drop down menu boxes are at the bottom of the Save as dialogue box. These 3 boxes should read EXACTLY as shown in Figure B and written below to properly save this file with the correct name and format (configuration file - *. File name: rq- sssp- client. Save as type: All Files Encoding: ANSI Click on SAVE and you can now exit out of NOTEPAD. File Placement - Placing both files in the same folder Find the file rq- sssp- client. SIMPLIFY STARTING THE PROTOCOL Each time you shut down your PC you will have to restart the file rq- sssp- client. To simplify this task go to the NEW FOLDER where the file rq- sssp- client. After the shortcut shows up in the folder drag and drop it onto your quick launch bar. Now you can easily start the protocol with a single click of your mouse. NEXT: INSTALLING THE NEW FIRMWARE AND A CHANNEL LIST INTO YOUR COOLSAT AND SETTING IT UP FOR NFPS. STEP 7. UPDATE WITH THE RQ FIRMWARE. First do a factory reset of your Coolsat to return it to the factory default settings (not to be confused with loading the factory bin file which should not be necessary) then follow these directions to update your current bin file with the rq- coolsat firmware that was included in your download for your Coolsat model. Follow the simple steps below to LOAD THE NEW RQ firmware/bin file 0. Turn power OFF on your Coolsat with the front button. Turn OFF rear power switch. Unplug the Coolsat 0. With all power OFF, connect the RS2. Coolsat to your PC 0. Plug in the receiver 0. Start the Coolsat Pro Loader v. FIGURE C BELOW). Turn power ON using the rear switch and turn ON the front power button. Locate the file for your Coolsat 4/5/6. Coolsat 4. 00. 0) 0. Use the Browse button in the loader to select the Coolsat 4/5/6. If port setting is correct, the Com port and current bin version loaded to the receiver will show 1. Click Exit to exit the Auto Detect 1. Click on the Connect button another window will open then click on the Start button to continue the programming. You will see System Reset, Sending percent, Sending Ok and Erasing the bin. Do not interrupt this process until the ! The Finish window will show the prior version of bin loaded. Exit out of the Coolsat Pro Loader program by clicking on the . Turn OFF your Coolsat using the rear switch. STEP 8. LOADING A CHANNEL LIST If using a channel list use the following procedure to load it into your Coolsat Receiver. Channel list - Use the *.
6 Comments
robert
3/29/2020 12:48:09 am
ok thank
Reply
robert
3/30/2020 01:33:30 am
can I download this file
Reply
robert polson
3/30/2020 02:06:46 am
can I download this software
Reply
robert polson
3/30/2020 02:52:17 am
well I get alone with every body. and love to have fun
Reply
robert polson
4/6/2020 02:25:35 am
I been trying to ge this loader but I had no lucj
Reply
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
August 2017
Categories |